TPC 2026
TPC 2026

 

 

Navigation: PLSS - Public Land Survey System > Double Proportion - PLSS >

Double Proportion dialog

 

 

 

 

This dialog computes the position of a lost corner using Double Proportionate Measurement.

You can initialize most of the dialog data by selecting the lost corner (assuming you've already created a record position) in a traverse before opening this dialog.

BLM Method

The method used is that described in the 2009 BLM Manual of Survey Instructions. The reports will include the text "BLM Manual" in the report headings to remind you of the method used on any printouts.

Steps

1.Recall the existing (controlling) corners.

2.Recall the Lost Corner (TPC inverses the existing corners) or enter the record data.

3.Recall the Temporary Corner (TPC inverses the existing corners) or enter the retrace data.

4.Choose Summary to check the computations.

5.Enter a Computed Point (you can reuse the Lost Corner label to update it's position) and choose Save.

If you have closed this dialog and wish to re-open it with all the data intact (without re-initializing), use the COGO command from the TPC desktop to open this dialog.

Existing Corners - North, South, East, West

Recall the existing (controlling) corners in the Retrace group box at the top of the dialog. You cal also left click the pick [>] button located next to each point then left click the existing corner point symbol or label in the drawing. When you recall an existing corner, TPC inverses it's direction and distance to the temporary corner and displays that inverse in the dialog.

Recalling Lost and Temporary Corners

When you recall an existing Lost or Temporary corner, TPC computes the inverses for any bearing or distance you have not already entered. So if you have already computed a record position for the lost corner or a temporary position based on a retracement, you can quickly populate the dialog data by recalling those points.

Note: Points that you recall in this dialog are not recomputed by this dialog. Their coordinates and point label are copied into the dialog only for the purpose of computing the record and retracement data.

Assuming the Temporary Corner is at a Midpoint

If you have not physically measured between the existing corners, you may want to assume the temporary corner is at the midpoint between the existing corners. TPC lets you do this easily in this dialog using equations. Lets look at the following example:  EastCorner----------(midpoint)----------WestCorner

•For the East corner bearing, enter EastCorner..WestCorner and press [Enter].

•For the East corner distance, enter EastCorner..WestCorner/2 and press [Enter].

•For the West corner bearing, enter WestCorner..EastCorner and press [Enter].

•For the West corner distance, enter WestCorner..EastCorner and press [Enter].

Dividing the inversed distance between the two corners by 2 created retrace data to the assumed midpoint.

Entering Directions

All directions in this dialog are entered from the existing corner to the lost or temporary corner. If you need to add 180° to an azimuth, enter the azimuth you have in any direction field with a '+ 180' as in  120.30 + 180. TPC will reverse the azimuth you entered.

[x] Recall direction and distance with equations

Turn this option on to enter equations, like 7..8, for any bearing or distance.  TPC will enter that equation for the corresponding bearing or distance and both will be computed with the one equation entered.

If you will be entering bearings and distance without equations, turn this off.

Entering Record Distances

TPC assumes the record distances you are entering are in the same units as the survey. If not, select their units from the pull down list in the Record group box. This allows you to enter record data in any units desired.

Computing the Lost Corner

The computed position of the Lost Corner is updated with each change you make to the data in the dialog. Any time you choose Summary or Save the computed point, you are using the current computed position. The Summary button is a great way to see how TPC has computed the lost corner.

The computed position of the lost corner is not actually used until you Save the computed point.

Saving the Computed Lost Corner

You can update any existing survey point with the computed lost corner coordinates by recalling its point label in the 'Computed Position of Lost Corner' field. TPC will ask if you want to update the existing point with the computed coordinates. Say Yes.

You can also save the computed position to any new survey point by entering an unused point label.


Related Topics

Cadastral Surveys

Editions

Professional

 

 

 

Copyright © 2026 Traverse PC, Inc.