TPC 2026
TPC 2026

 

 

Navigation: Drawings > Drawing in TPC - It's Not CAD >

Paper Space vs. Survey Space

 

 

 

 

One of the exciting features of Drawing View is the concept of Paper Space vs. Survey Space.


Paper Space

Paper Space refers to drawing objects like the title block and north arrow that you place on the drawing page irrespective of the survey position and scale.

The title that you add to the drawing is a good example. You might want it to start one inch down from the top of the border and one inch over from the left of the border. If you move or scale the survey, you don't want the title to move with it. In paper space, it won't.

Paper space also helps when you have to change drawing sizes. In paper space, the title is always an inch from the top and inch from the left, no matter what page size you choose.

All paper space objects are positioned on the page in inches.

Paper Space coordinates are in inches from the border of the drawing. Positive coordinates are the inches from the left side and bottom of the border. Negative coordinates are from the right side and top of the border. For example, if you place a paper space object one inch from the top and two inches from the right, the coordinates will be X=–2.0 and Y=-1.0. These coordinates are displayed on the status bar along with the survey space coordinates.

When you change page sizes, the paper space coordinates do not change. If an item was three inches from the bottom of an 8.5” x11” page, it will be three inches from the bottom of an 11” x17” page.

As you move an object on the page you will notice that Drawing View changes its coordinates to reflect the side it is nearest. If, for example, you move an object to the right, as you pass the center of the page you will notice the X paper space coordinate change from positive to negative to indicate that the object is now closer to the right border than the left.

Paper Space in TPC has a strong correlation to paper layouts in CAD drawings.  See Using Layouts.


Survey Space

Survey Space refers to drawing objects like point labels and line annotations that are tied to the survey. As you scale and position the survey, these objects are sized and positioned with it.

A good example of a survey space object is a monument note that you want to show on the drawing. You will draw the note near the point it pertains to. If you want, you can include a leader from the descriptive text to the point itself. Both the text and the leader would be drawn in Survey Space. Now as you position the drawing on the page, the text and leader move with the survey.

When you view a traverse, you are viewing it in survey space. When you change the Control Point, Side Shot, and Lot Label settings, you are changing the survey space objects drawn by Drawing View.

Those of you who have used other CAD programs have worked almost entirely in survey space or what your CAD program may have called “World Coordinates”.

Survey Space in TPC has a strong correlation to model space in CAD drawings.  See Using Layouts.


Survey Objects

TPC will sometimes refer to Survey Objects, which are objects created by survey data, like points, traverses and surfaces.  These objects are created by the survey data, using Traverse Drawing Settings or Surface Settings.

Survey Objects always reside in Survey Space, but this distinction allows you to manually add drawing objects in Survey Space that are not Survey Objects.


Paper Space Mode

As you add objects to a drawing, they will either be in paper space or survey space depending on the mode of the drawing. Once the object has been created, you can change it from paper space to survey space or visa versa, but Drawing View gives you a handy way to keep track of the mode while you are adding objects.

•Choose View | Paper Space Mode.

If the Paper Space Mode command is on, the drawing is in Paper Space Mode and any new objects you create will be paper space objects. If this command is not checked, the drawing is in Survey Space Mode and any new objects you create will be survey space objects.


Deciding Which Space is Correct

This is simple.  Because Survey Space objects have survey coordinates and Paper Space objects have paper coordinates, simply think about how you are positioning the object.  If you are positioning the object relative to a survey object such as the side of the property or along a road, the object should be in Survey Space.  If you are positioning the object where it looks good on the sheet of paper such as a drawing title or survey narrative, the object should be in Paper Space.


Delineating Space

If you accidentally create an object like a narrative in survey space, then move the survey on the page, the object will move with the survey and you will probably end up moving it back to its correct position, then changing it from Survey Space to Paper Space.  Because it can be difficult to see which objects are actually in what space unless you hover over each object, there needs to be a way to display them.  To see which objects are in Survey Space, choose View | Delineate | Survey Space Objects.  To see which objects are in Paper Space, choose View | Delineate | Paper Space Objects.


Changing an Object's Space

Sometimes you may find yourself adding text or lines in paper space mode when you thought you were in survey space mode or visa versa. Once you discover the error, you need some way to convert the objects from one space to the other.

One way to do this is to right-click an object and choose Modify Objects | Toggle Space.  This will toggle, or flip, the space of the object to the opposite space.  In other words from Paper Space to Survey Space or vice versa.  You can even Edit | Select Objects to select multiple objects in either or both Paper Space and Survey Space to toggle all of them at one time.  This is the recommended method for handling multiple objects that are in the incorrect space.

Another way to change the space of individual objects is available in the object Properties:

•Move the cursor over the object. The status bar will indicate the object name and information.

•Right click and choose Properties.

•Turn the [X] Paper Space toggle on or off.

•Choose OK.


Related Topics

Drawing Page Layout
Paper Space Mode command
Delineating Drawing Objects
Using CAD Layouts

Editions

Personal, Premium, Professional

 

 

 

Copyright © 2026 Traverse PC, Inc.