TPC 2026
TPC 2026

 

 

Navigation: Alignments > Horizontal Curves >

Entering Horizontal Curves

 

 

 

 

You typically enter horizontal curves in a traverse as you enter data from a legal description or plat. 

The way you enter the curve depends on the geometry of the alignment and the information you have, but typically, you enter what you have and TPC computes and displays the rest.


Enter Curve Data for Existing Lines

Sometimes you want to specify curve information for an existing line (chord). This is typical of deed descriptions that calls the bearing and distance of the chord, plus the radius and direction (clockwise or counter clockwise) of the curve.

•Choose View | Format View... and include the curve information you want (R=Radius, C=Arc Length, etc.).

•Enter the chord bearing and distance.

•Highlight the point that will be the PT (Point of Tangency) of the curve.

•Enter the radius, arc length, tangent or delta. A negative radius or arc length indicates a counter clockwise curve.

The Traverse View will display PC and PT in the Type column indicating the Point of Curvature and Point of Tangency.

If you include other curve columns in the display sequence, TPC will compute the other curve parameters and display them for you.

Note: In this situation, TPC may not store the curve data you entered as raw data for that traverse point. Instead, TPC will compute the corresponding grid radius for the curve and store it with the line from the PC to the PT. Raw curve data is only stored with a traverse point if that data is used to compute the PT of the curve.


Raw Data

If you enter enough raw data (radius, delta, etc) for TPC to compute the curve, TPC will store the raw data. TPC is then free to use this stored raw data to recomputed the position of the PT and any related curve information. This is how you keep an alignment dynamic, allowing you to recompute the alignment as you edit it.


Creating Curves as You Go

You can also enter curves as you go, creating the PT position and curves at the same time.

•Use the arrow keys to append a new point to the traverse.

•Enter two pieces of curve data (i.e. Radius and Delta, or Arc Length and Delta, etc.).

•The Traverse View will display PC and PT in the Type column, indicating the Point of Curvature and Point of

If you include other curve columns in the display sequence, TPC will compute the other curve parameters and will display them for you.


Adding a Tangent Curve to a Traverse

When you add a curve to the end of a traverse, so that TPC adds the PT position and curve at the same time (described above in Creating Curves as You Go) and don't provide any curve parameters with direction (i.e. PC->PR bearing), TPC assumes you want the curve to be tangent to the preceding traverse course.

The preceding tangent course can be a tangent, curve or spiral.

Compound Curve

If the preceding course is a curve and you enter a new curve of the same direction (CW vs CCW) but a different radius, you will create a compound curve.

Reverse Curve

If the preceding course is a curve and you enter a new curve of the other direction (CW vs CCW), you will create a reverse curve.


Adding a Non-Tangent Curve to a Traverse

To add a non-tangent curve to a traverse, enter your curve information and include any curve data that establishes the orientation (direction) of the curve.  This can be a chord bearing, PC->PR bearing or PR->PT bearing.  You can also use the Horizontal Curve Dialog to specify the PC->PI bearing.

When TPC encounters any curve orientation data like those just described, that orientation is used for the curve.


Recalling the Outgoing Curve Tangent

Create a new traverse point immediately after the curve.

•Move the cursor to the Bearing, North Az or South Az column.

•Press [Space], then [Enter].

TPC will compute the outgoing tangent direction and use it as if you had entered it.  The next traverse course that uses the outgoing curve tangent can be a tangent, reverse curve, compound curve or spiral.


Curve Data Combinations

There are many combinations of curve data that you can enter right in the Traverse View to compute a curve. Although the radius and arc length are common, you can lots of combinations. Here are a few.

•Radius and Central Angle.

•Radius, PC->PR and PR->PT. TPC computes the central angle, then computes the curve.  See Using Radius Points Sample.

•Radius, Chord Bearing and Chord Distance.


Cul-de-sacs

You create cul-de-sacs by telling TPC that the central angle of a curve is > 180° in the Horizontal Curve dialog. 

See Cul-de-sacs.


Specifying a Point of Intersection Point Type

Highlight the point label field of the point that you want to be a PI.

•Choose Type | PI=Point of Intersection.

When you highlight a point that has been designated as a PI and select the horizontal curve dialog box, TPC looks for a PC and PT on either side of the PI. If it does not find a PC and PT, it inserts them automatically when curve data is entered. The inserted points will have the same point label as the PI, but with the extensions PC and PT.

In all other respects, PIs are treated like occupied points. This is a great way to float in PCs and PTs.


Entering a Curve at a Horizontal PI

•Choose View | Format and include the curve information you want (R=Radius, C=Arc Length, etc.).

•Highlight a point of intersection (the Type column displays PI).

•Enter the known radius, tangent or arc length (the delta is determined by the PI and cannot be entered).

TPC will insert a PC point before the PI and a PT point after the PI if they do not already exist. Both the inserted PC and PT points will be positioned on the tangents, equal distance from the PI. The Traverse View now displays the inverse between the PC and PT (as if the PI was a side shot from the PC). The PC and PT are treated like occupied points from then on.

To remove the curve at a horizontal PI, enter zero for the Radius.

See Points of Intersection (PI).


Related Topics

Entering Horizontal Curves
Using Radius Points Sample
Cul-de-sacs

Editions

Personal, Premium, Professional

 

 

 

Copyright © 2026 Traverse PC, Inc.