TPC 2026
TPC 2026

 

 

Navigation: Sharing Data (Importing / Exporting) > Importing Survey Data >

Import Ground Traverse Settings

 

 

 

 

When you import ground traverse data (angles, distances, occupied points, backsights, etc.), you can tell TPC how exactly to handle the data.

 

The following options are available for some ground traverse file types, like Trimble .dc, TDS .RW5 and .RAW files and others.


Add Stored Points to Traverse

Some file types, like the Trimble DC10.70 shown here, can store points in their files.  These are typically points that have been imported into the project for use in the field, and are exported back out with the project.

Turn this option On to include them in the traverse created by the [x] Add Stored Points to Traverse option.

Turn this option Off to not include them.  They will still be imported into the survey, and you can see them in the Points Manager.

Warning: When importing raw data, like angles and distances, you may need to turn this option Off to get the correct OP, BS, FS sequence, especially when angle sets are involved.


Treat First Observation as Backsight

Many data collectors include a backsight record (TDS uses a BK records) for each instrument setup. However, if your data collector does not, or if a backsight record is omitted, TPC can treat the first observation as the backsight observation and create a backsight record for it in the traverse.

Use this option to treat the first observation after a station record as a backsight observation.


Combine BS, OP and FS

Use this option to eliminate redundant points in the traverse created from the import.

The TDS file format, for example, includes the following records for each foresight (OC-station, BK-backsight and TR-foresight). This results in the following traverse point sequence.

1           OP

99           BS

2           SS

2           OP

1           BS

3           SS

3           OP, etc.

This option reduces this sequence to the following

1           OP

99           BS

2           FS

3           FS, etc.

This format is much cleaner to work with and is typical of how the traverse would look if you had entered the data manually.


Convert Horizontal Circle to Angles

Most total station data formats provide the horizontal circle reading. Internally, TPC stores the circle readings, allowing you to have a non-zero backsight reading. Inside the Traverse View, the raw data mode displays these circle readings, while the inverse move displays the resulting horizontal angles that were turned from the respective backsights.

Use this option to convert horizontal circle readings to angles. TPC does this by subtracting the BS circle reading from any observations and setting the BS circle reading to zero.

Some surveyors set the BS circle to the reference azimuth of the BS. Any angles turned can be read as a direct azimuth if desired. TPC computes these observations just fine, but if you then copy data to another traverse and include raw data you can loose the association of the circle reading and its original backsight. Converting from a circle reading to the resulting angle can eliminate the side effects of these actions.


Rotate / Translate to [=label]

Turn this option on to have TPC automatically rotate and translate the imported data to the positions of existing survey points.

Both the initial occupied point OP and backsight point BS must include the point labels of the points to translate and rotate to in the point descriptions of the imported points. 

For example, if TPC imports 1 OP = 100 followed by 2 BS = 101, and finds existing points 100 and 101, it will

•translate all the imported data so that imported point 1 is at the same position as the existing point 100

•rotate all the imported data so that the bearing from imported point 1 to imported point 2 is the same as the bearing from existing point 100 to existing point 101

•TPC will then compute the rest of the imported traverse, using the raw data, based on the updated positions of points 1 and 2


Apply Prism Constant if Found

Some formats, like the Trimble DC10.70 do NOT automatically include prism offsets in recorded slope distances.  Turn this option On to include them.

Check with your instrument manufacturer to see if they are included.

If [X] Details is turned on, you will see this in the report - Applied prism offset 0.072.

SS:306  Desc:RBF

  SD:592.0272  ZA:91.19639000d  HC:189.44091000d  HT:5.00

  Applied prism offset 0.072,  Applied PPM -0.00848

 


Apply PPM if Found

Some formats, like the Trimble DC10.70 do NOT automatically correct recorded slope distances for temperature and pressure via a Parts Per Million (PPM) adjustment.  Turn this option On to include this adjustment.

 

Check with your instrument manufacturer to see if they are included.

If [X] Details is turned on, you will see this in the report - Applied PPM -0.00848.

SS:306  Desc:RBF

  SD:592.0272  ZA:91.19639000d  HC:189.44091000d  HT:5.00

  Applied prism offset 0.072,  Applied PPM -0.00848

 


Related Topics

Importing Survey Data
Exporting Data
 

 

 

 

Copyright © 2026 Traverse PC, Inc.