|
A traverse is a collection of points that belong together for some reason. By combining the sequence of points with the traverse Point Types, you can achieve just about any combination of data you want.
Traverse Point Types
A traverse is also defined by its Point Types - like RTK, side shots, backsights, benchmarks, offsets, PIs and others.

In this example, we have a typical start to a total station traverse used in a site survey (gathering information).
•CS2 - the control point where the instrument is setup.
•CS9 - the backsight for the shots that follow
•CS10 - a sideshot to another control point (probably used to double check the setup before continuing on)
•1-5 - side shots with descriptions.
This is very typical of how Point Types and Point Sequence combine to start a traverse.
Notice the status bar at the bottom of the Traverse View. When the Horiz Angle for side shot 2 is selected, it indicates the backsight (BS), occupied point (OP) and foresight (FS) that the angle belongs to.
Point Types
Here is a list of the point types you may see in a traverse
(blank) Occupied Point / Foresight / Control Point GNSS Base, Hotkey: Ctrl+F10 - you see this a lot as you enter deed descriptions or your field data (GPS or conventional) SS - Sideshot, Hotkey: F10 SSM - Sideshot Mean - derived from an angle set BS - Backsight, Hotkey: Shift+F10 BM - Benchmark RS - Resection RTK - GPS/GNSS RTK/RTN rover point OFS - Offset (perpendicular) OFX - Cross-Section OBS - Observation used to create redundancy for Least Squares networks PI - Point of Intersection (horizontal tangent intersect) PC - Point of Curvature, compound curvature or reverse curvature of a horizontal curve PT - Point of Tangency of a horizontal curve BC - Beginning of Curve of a vertical curve EC - End of Curve of a vertical curve VPI - Vertical Point of Intersection (vertical tangent intersect) TS - Tangent to Spiral SC - Spiral to Curve CS - Curve to Spiral ST - Spiral to Tangent F1, F2, F4, B1, B2 - angle set components FSM - Foresight Mean derived from an angle set Note - A note inserted between two other traverse points Gap - GAP point tells TPC not to draw the line or labels at this location Front, Side, Back - lot setback type
Specifying a Point Type
Point types are specified in the Traverse View by choosing Edit | Point Type and selecting a type from the list. Some of the most common of the types have hot keys and there is also a Point Type toolbar available in the Traverse View. The point type you select is applied to each selected (highlighted) point in the Traverse View, so it's easy to change multiple points with one command.

Control Point
A control point is a very general point type in TPC that simply indicates that this point is used as the starting position for any subsequent computations. Any additional points added to the traverse are computed from this control point. So a control point could be followed by 20 sideshots, each of which is computed from that control point. When another control point is entered, additional points added to the traverse are computed from it.
Point Type Raw Data 1 Point 1 is the first control point, from which the sideshots 100 and 101 are computed. 2 BS Point 2 is the backsight used to orient the following shots. 100 SS yes 101 SS yes 33 Point 3 is the next control point from which the sideshot 102 is computed. 102 SS yes Point 2 is assumed to be the backsight because no other BS point was specified.
Control points do not display a Point Type in a traverse unless they are part of a horizontal or vertical curve (i.e. PC, PT, BC, EC, PI, TS, SC, CS, ST).
BS - Backsight
Backsights are use for conventional surveys (total station or theodolite). Unless a backsight point is specified, TPC always assumes that the previous control point is the backsight. You can confirm this by selecting any horizontal angle in a traverse and reading the Status bar where TPC will display 'BS=xx". It also assumes that the backsight circle reading is zero (you zeroed the gun on the backsight)
You include a backsight point in TPC for any of these reasons:
•you want to use a backsight point other than the previous control point
•the backsight circle reading is other than zero
•you recorded a distance to the backsight (maybe as a double check)
•the backsight point changed (some equipment operator knocked it over and you need to choose an alternate point)
Foresights
Foresights are just another form of Control Point in TPC that contains Raw Data used to compute the position of the foresight (from the previous Control Point) then establish the foresight as the next control point. This creates an ambiguous situation since the foresight could display FS to indicate it is a foresight or be left blank to indicate it is a Control Point. As a result, TPC does not display FS for the Point Type, but leaves it blank like any other Control Point.
The one exception is when the foresight has been computed from an angle set. In this case, TPC displays FSM, indicating that is is a Foresight Mean.
SS - Sideshot
A sideshot always originates from the previous control point but no other points are computed from it. You can always recall any sideshot later on as a control point, but in the current sequence, it is the end of the line. See Entering Sideshots.
The sideshot point type also determines how the point is drawn when the traverse is tagged in a drawing. All sideshots and offsets are drawn using the traverse's Sideshot settings.
SSM - Sideshot Mean
When a sideshot is derived from an angle set, TPC displays SSM instead of SS to indicate that the displayed data is the mean of the angle set's observations.
BM - Benchmark
A benchmark is an observation to a point of known elevation. TPC computes the elevation difference to the total station, thereby establishing it's elevation independent of the control point's elevation. The Instrument Height displayed is actually the computed difference between the elevation of the gun and the control point.
The benchmark shot always follows the backsight shot.
RS - Resection
Resections are shots taken to other control points, who's positions are known, in order to establish the position of their preceding control point.
You can include any number of resection shots after a control point. If only two resections points are included, TPC does a standard 2-point resection. If more are included, TPC does a simple Least Squares resection.
RTK - GPS/GNSS RTK/RTN
When you import RTK (Real Time Kinematics) or RTN (RTK Network) points, TPC treats any base points like control points and rover points get the RTK point type.
See GNSS Traversing.
OFS - Offset
An offset point is a special kind of sideshot. Like a sideshot, it originates from the previous control point then stops. Unlike a sideshot, the direction component (azimuth, bearing or horizontal angle) is optional. If an Offset includes a directional component, it is computed just like a sideshot.
However, if an Offset does not have a directional component, it assumes that the offset it perpendicular to the alignment created by the control points. Offsets are capable of bisecting the angle if the control points define tangents and is capable of computing perpendicular offsets to curves and spirals where appropriate. In this case, the sign of the distance data is used to compute the side of the alignment the offset is on. Positive distances compute offsets to the right. Negative distances compute offsets to the left.
The nice thing about Offsets is that if the alignment changes, the Offsets recompute their positions automatically to remain perpendicular to the alignment.
OFX - Cross-Section
Cross section points can not be created in this version but are supported from previous versions. A cross section point works just like an Offset but originates from the previous Control Point, Offset or Cross Section point.
OBS - Observation
An observation is any point that contains data but does not actually compute its point. All of the angle set types (F1, F2, etc) are observations. They hold data for an angle set but don't actually compute the point until they are meaned.
The OBS point type indicates an observation that is not part of an angle set. Like any observation, they contain raw data measured to a point but do not compute that point. OBS points are used to build redundancy for Least Squares computations.
PI - Point of Intersection
A Point of Intersection is a special kind of Control Point that defines the central angle of a curve or spiral by its incoming and outgoing tangents. Designating a Control Point as a PI does not change the central angle it merely tells TPC that the included central angle is available for curve and spiral computations. So you can enter one more piece of curve data, like a radius, and TPC has everything it needs to compute the curve. Or enter additional spiral information and TPC has everything it needs to compute the spiral.
In addition, PI's have the ability to float in their curve points. When you enter a radius for a PI, TPC automatically inserts the corresponding PC and PT for the resulting curve into the traverse. Change the radius value and the inserted PC and PT float along their respective tangents to match the resulting curve.
F1, F2, F4, B1, B2 - angle set components
These point types are components of a horizontal angle set. They are always followed by a SSM (sideshot mean) or FSM (foresight mean) point.
FSM - Foresight Mean
A Foresight Mean is a special kind of Control Point that includes Raw Data generated from the preceding angle set.
Note
A Note is a special kind of description that is not tied to a specific point, but rather is part of the traverse's point sequence. Many data collectors use notes to store information about the field data being collected.
Gap
When you insert a Gap point into a traverse, you are telling TPC not to draw the line or labels at this location. In other words, you are creating a gap.
Related Topics
Traverses Point Types Resections Entering Sideshots Sideshot settings GNSS Traversing horizontal angle set Gap
Editions
Personal, Premium, Professional
|